- Product description
- with the Autoterm Air 2D heater
- with the Autoterm Air 4D heater
- Shipping and Returns
- Technical Support
Our 6L water heater is specially designed to provide you with hot water during your travels in a van, Motorhome, or converted van.
REF: 75715 (12V), 75716 (230V) or 76005 (24V)
Air 6L Water Heater - Pundmann
Model: Water heater Pundmann Air 6L
Description:
With your Autoterm air heater and your Pundmann water heater, you can both heat your cabin and your water.
The boiler uses the heat from the heating to warm the water. It is also possible to turn on the water heater without turning on the heating.
The parts we recommend to assemble them are listed below.
This water heater is compatible with Autoterm Air 2D and Autoterm Air 4D air heaters.
Warning: the pressure associated with the water heater is 2.3 bar or less. So do not forget to check the pump you have on your circuit and if it is not suitable, do not hesitate to take a pressure reducer and set it to 2.3 bar.
Installation:
Purge the water heater to ensure there is no air left in the circuit. Place the water heater in the correct position, with the valve facing down. Also, do not start your water heater if it is empty!
Note: The valve is supplied with the water heater
The water heater has two heating modes that you can use independently of each other, which makes this an autonomous water heater. The heating element, available in 12, 24 or 230V, can heat your water when your vehicle is running (for 12 V, 24V). The 230V can heat your water when you are connected to a hookup point at a campsite for example. The water heater uses the heat from the heating to warm the water. As you have seen, it is also possible to turn on the water heater without turning on the heating. With Pundmann, benefit from a 12v, 24v or 230v water heater.
Important information
You must absolutely have a pump (water group) to use your water heater. If this pump is higher than 2.3 bar a pressure reducer will be necessary.
Installation advice:
You can install a 60 Y bypass fitting for the 2D or a 90mm one for the 4D to divert the hot air from the heating to the outside of the vehicle in summer when you do not need to heat the cabin.
Important information:
You must install a 90 - 60 mm adapter between your water heater and the heating if you have an Air 2D!
Technical specifications:
|
Operating pressure: |
2.3 bars or less |
|
Heating time: |
12 V: about 90 minutes |
|
Water connection tube diameter: |
Ø 10 mm |
|
Average consumption 12V 200W - 24V 400W - 230V 500W: |
16A/H - 16A/H - 2A/H |
|
Hot air hose connection: |
Ø 90 mm |
|
Material: |
stainless steel tank, polyester coating |
|
Dimensions (LxWxH): with valve |
23x46x23cm |
|
Weight: |
6kg |
|
Power cable length: |
96 cm |
|
Cable diameter: |
4 mm |
|
Safety valve: |
3.0 bars |
Installation diagram with the Air 2D/4D forced-air heater:
Recommended parts:
2xAdapters ⌀ 90-60 mm Pundmann + Air 2D 69934
Heating duct 60 mm DE013
Control cable for the Y bypass FR054
Y bypass ⌀ 60 mm FR011
Air vents ⌀ 60 mm (category: air duct)
Adjustable thermostatic mixer AT0062
Heating duct 90 mm DE015
Control cable for the Y bypass FR054
Y ⌀ 90 mm with control valve DE037
Air vents ⌀ 90 mm (category: air duct)
Adjustable thermostatic mixer AT006
Delivery and returns
-
Delivery 24–48h 🇪🇺 Europe: Shipping to France and Western Europe (Portugal, Spain, Italy, Greece, Germany, Netherlands, Belgium).
-
Delivery 🇬🇧 United Kingdom & 🇨🇭 Switzerland: Additional average delay of 24–48h due to customs procedures.
-
Returns: 30 days to exchange or return your products.
2-year product warranty
